Browse wiki

jump-to-nav Jump to: navigation, search
SE196:/MS02
MS Description Methanol, isopropanol, and acetonitrile of Methanol, isopropanol, and acetonitrile of LC-MS grade were purchased from Wako. Ammonium acetate and EDTA were purchased from Wako and Dojindo, respectively. Milli-Q water was purchased from Millipore. SPLASH Lipidomics I or EquiSPLASH used as internal standards were purchased from Avanti Polar Lipids. <LC Method> The LC system consisted of a Waters Acquity UPLC system. Lipids were separated on an Acquity UPLC Peptide BEH C18 column (50 x 2.1 mm; 1.7 µm) (Waters, Milford, MA, USA). The column was maintained at 45°C at a flow-rate of 0.3 mL/min. The mobile phases consisted of (A) 1:1:3 (v/v/v) acetonitrile:methanol:water with ammonium formate (5 mM) and 10 nM EDTA and (B) 100% isopropanol with ammonium formate (5 mM) and 10 nM EDTA. A sample volume of 0.5-3 µL, which depended on biological samples, was used for the injection. The separation was conducted under the following gradient: 0 min 0% (B); 1 min 0% (B); 5 min 40% (B); 7.5 min 64% (B); 12 min 64% (B); 12.5 min 82.5% (B); 19 min 85% (B); 20 min 95% (B); 20.1 min 0% (B); and 25 min 0% (B). Sample temperature was maintained at 4°C. <MS Method> Mass spectrometric detection of lipids was performed on a quadrupole/time-of-flight mass spectrometer TripleTOF 5600 or 6600 (SCIEX, Framingham, MA, USA). All analyses were performed at the high resolution mode in MS1 (~35,000 full width at half maximum (FWHM)) and at the high sensitivity mode (~20,000 FWHM) in MS2. Data dependent MS/MS acquisition (DDA) was used. The parameters were MS1 and MS2 mass ranges, m/z 70-1250; MS1 accumulation time, 250 ms; MS2 accumulation time, 100 ms; collision energy, +40/-42 eV; collision energy spread, 15 eV; cycle time, 1300 ms; curtain gas, 30; ion source gas 1, 40(+)/50(-); ion source gas 2, 80(+)/50(-); temperature, 250°C(+)/300°C(-); ion spray voltage floating, +5.5/-4.5 kV; declustering potential, 80 V. The other DDA parameters were dependent product ion scan number, 16; intensity threshold, 100 cps; exclusion time of precursor ion, 0s; mass tolerance, 20 ppm; ignore peaks, within m/z 200; and dynamic background subtraction, True. The mass calibration was automatically performed using an APCI positive/negative calibration solution via a calibration delivery system (CDS). n via a calibration delivery system (CDS).
MS ID MS02  +
MS Instrument LC, Waters Acquity UPLC system; MS, AB Sciex TripleTOF 5600+ or 6600 system  +
MS Instrument Type UPLC-QTOF-MS  +
MS Ion Mode Positive and Negative  +
MS Ionization ESI  +
MS Title Method 2: SCIEX TripleTOF DDA normal mass range method  +
Modification dateThis property is a special property in this wiki. 26 December 2019 06:19:05  +
hide properties that link here 
  No properties link to this page.
 

 

Enter the name of the page to start browsing from.
Personal tools
View and Edit Metadata
Variants
Views
Actions
Toolbox